Updated on 17 November 2026
How to get water out of a phone speaker
After a splash, a swim or the rain, your phone sounds dull or crackly: water is trapped in the speaker. Here is how to clear it safely, in order.
Why the sound gets muffled
A speaker makes sound by vibrating a thin membrane. When a drop gets stuck in the grille or behind it, the membrane cannot move freely: the sound turns dull, weak or distorted.
It is usually temporary. The water eventually evaporates, but you can help it leave faster, as long as you avoid the moves that make things worse.
Water-resistant does not mean water-proof
Most recent phones are rated IP67 or IP68: they withstand fresh water at a limited depth and for a limited time, under laboratory conditions. Seals age, a drop or a repair weakens them, and the rating does not cover salt water, chlorinated water or drinks.
Even on a water-resistant phone, a drop can lodge in front of the speaker membrane: there is no leak, but the sound is muffled. It is the most common case, and the easiest to fix.
What to do right away
- Remove the case, headphones and any plugged-in accessory.
- Wipe the outside with a soft, dry cloth.
- Do not plug in a charger while the charging port is wet.
- After sea water or a sugary drink, rinse with fresh water, then dry: salt and sugar damage contacts as they dry.
The step-by-step method
- Hold the phone upright, speaker facing down, and shake it gently in your palm: the water runs toward the opening.
- Lay it speaker down on an absorbent cloth, in a dry, airy place, in the shade.
- Play a low, undulating sound at high volume, speaker facing down: the vibrations help the membrane push the water out. This is the principle behind ToneDry, with a 30-second cycle.
- Compare the sound before and after, then repeat once or twice if needed.
- Let it dry for an hour or two before putting the phone away or charging it.
Depending on the situation
| Situation | What to do | Usual time |
|---|---|---|
| Splash or light rain | Wipe, speaker facing down, one sound cycle | A few minutes |
| Pool (chlorinated water) | Rinse with fresh water, dry, sound cycle, wait | 1 to 2 hours |
| Sea (salt water) | Rinse carefully with fresh water, dry, do not charge while the port is wet | 2 hours, sometimes more |
| Shower, bathroom steam | Leave in open air, avoid direct heat | A few hours |
| Dropped in water, long immersion | Switch off, dry the outside, do not charge, see a repairer | As the repairer advises |
Why a low sound helps
At low frequencies the membrane moves with a larger amplitude: it pushes the water out of the grille instead of merely shaking it. It is the same idea as the water-eject feature of some smartwatches.
Keep cycles short and hold the phone away from your ear: a loud low sound is not meant to last, neither for your ear nor for the speaker.
How to tell whether the water is really out
- Play a familiar sound at medium volume: it should be clear, without crackle, and as loud as before.
- Run a stereo test: if only one side sounds weak, there is probably still water.
- Make a call or record a voice message: the microphone may have taken water too.
- Try again after an hour: a sound that clears up on its own while drying is a good sign.
- If nothing changes after 24 hours, or if the sound has become permanently crackly, have the device checked.
What to avoid
- A hair dryer or any heat source: it can damage the membrane, the glue and the battery.
- Compressed air near the grille: it can push water and dust further in.
- Needles, toothpicks and cotton swabs, which can puncture the membrane.
- Rice: it is not very effective and can leave dust in the openings.
- Repeatedly charging or powering on a phone whose port is still wet.
When to see a professional
If the phone stayed submerged for long, took in salt water, has a foggy screen or camera, or no longer turns on, switch it off and take it to a repairer: a sound-based method does not replace full drying.
Frequently asked questions
How long does it take for the water to come out?
One to three 30-second cycles are often enough for a single drop. If the sound stays muffled, let the phone dry for an hour or two, then try again.
Does it also work for the microphone or the charging port?
Sound mostly helps the speaker. Water in the microphone or charging port is handled by letting it air-dry, without plugging in a charger until it is dry.
Can a low sound damage the speaker?
A loud low sound played for a long time can strain a speaker, which is why cycles are short and spaced out, and why you should keep the phone away from your ear.
Does rice dry a wet phone?
Barely, and it can leave dust. A dry, airy place, open air and a little patience work better.
My phone is water-resistant (IP68): should I still act?
Yes if the sound is muffled: water resistance protects the components, not the speaker opening. Wipe it, speaker facing down, and run a sound cycle. After salt or chlorinated water, rinse with fresh water before drying.
The speaker crackles after getting wet: is it serious?
Not necessarily: it is often residual water on the membrane. If the crackle persists after complete drying, the membrane or the amplifier may be damaged and a repair becomes necessary.
Do those “eject water” videos online work?
The principle is the same (a low sound that vibrates the membrane), but a video does not adjust the volume, check for headphones or compare the result. A dedicated app makes the method more reliable and safer for the speaker.
How many cycles should I run at most?
Two or three 30-second cycles are usually enough. If the sound stays muffled, it is better to let the phone dry for an hour or two than to stack loud cycles.
